Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
HEAVY DUTY MOTORCYCLE CHAIN
SPLITTER & RIVETING TOOL SET
MODEL No: MS025
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & CONTENTS
WARNING! Ensure Health and Safety, local authority and general
workshop practice regulations are adhered to when using tools.
DO NOT use this tool if any parts are missing or damaged.
DO NOT use this tool for any purpose other than that for which it is
designed.
Wear approved eye protection. A full range of personal safety
equipment is available from your Sealey dealer.
Wear suitable clothing to avoid snagging. Do not wear jewellery
and tie back long hair.
Maintain correct balance and footing, do not over-reach. Ensure
the floor is not slippery and wear non-slip shoes.
Keep children and other unauthorised persons away from the
working area.
Keep yourself and tools away from hot engine parts.
Maintain the tool components in a good and clean condition for
best and safest performance.
Replace or repair damaged parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the
warranty.
Ensure that the motorcycle is standing on a level surface and that it
is adequately supported on its own centre stand, or by other
means, before commencing any work.
Ensure that the motorcycle's engine is turned off.
DO NOT use this tool when you are tired or under the influence
of alcohol, drugs or intoxicating medication.
When work is completed, clean tools and replace in the carrying
case and store in a safe, dry, childproof location.
Comprehensive set designed to adjust length of motorcycle chains by
removing or adding links. Set is also ideal for use on horticultural and
agricultural machinery. Includes tools designed for riveting and plate
holder for connecting links accurately.
Contents:
Pin Holder, U-Holder, Plate Holder, Pins - 3, 4, 5mm,
Anvils - 3, 4, 5mm
fig.1
fig.2 - Disassembling a chain
3. OPERATION
Original Language Version
MS025 Issue: 1 - 02/11/10
IMPORTANT: These instructions are provided as a guide only.
Always refer to the motorcycle manufacturer’s service
instructions, or a proprietary manual, to establish the current
procedure and data, also any warnings or cautions particular to
the motorcycle.
Before commencing work, ensure that the tool is suitable for the
selected chain size and connecting link. Ensure that the new
connecting link is of the same size and type as the chain to be
connected.
The pins in this set are consumable parts and therefore not
covered by the warranty. When selecting a pin, ensure that it is not
too big for the chain pin, as it may jam in the chain, or too small, as
it may break.
3.1. Disassembling a chain.
3.1.1. Fit a suitably sized pin for the size of chain, into the pin holder
(fig.2.2). Ensure that it is pushed fully home. Ensure that the pin
holder is wound back into the body to allow enough space for it to fit
around the chain.
3.1.2. Position the matching sized anvil into the aperture in the U holder
and place the U holder over the chain link to be removed (fig.2.1).
3.1.3. Slide the pin holder body onto the U holder and tighten the securing
screw in position A (fig.2.3).
3.1.4. Ensure that the chain link is correctly positioned against the hole in
the anvil at the rear of the U holder, and screw in the pin holder until
the pin is touching the face of the chain link pin to be removed.
Check that everything is lined up.
3.1.5. Use a 27mm spanner to hold the pin holder body and a 19mm
spanner to turn the pin holder. Turn the pin holder clockwise and
proceed to start pushing out the link pin from the chain.
Re-check that all parts are lined up and that the pin is centred on
the link pin. Continue to push out the link pin (fig.2.4).
Note: If excessive resistance is felt initially and there is difficulty in
turning the pin holder, the pin may be too large for the link pin.
Try one size smaller pin and anvil if possible.
(2 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais