 WARNING! Ensure Health & Safety, local authority, and general

workshop practice regulations are adhered to when using this

equipment.

 WARNING!Disconnect the hammer from the air supply before

changing accessories, servicing or performing any maintenance.

 Keep the hammer clean and maintain it in good condition (use an

authorised service agent).

 Replace or repair damaged parts. Use genuine parts only.

Unauthorised parts may be dangerous and will invalidate the

warranty.

 Keep the work area clean, uncluttered and ensure there is

adequate lighting.

 Ensure chisels are correctly rated for the job, and DO NOT use

damaged or suspect chisels.

 WARNING! Wear approved safety eye or face protection, ear

defenders, and if dust is generated, respiratory protection.

 Keep hands and body clear of the work when operating the

hammer.

 Maintain correct balance and footing. Ensure the floor is not

slippery and wear non slip-shoes.

 Remove ill fitting clothing. Remove ties, watches, rings, and other

loose jewellery, and contain and/ or tie back long hair.

 Keep children and unauthorised persons away from the working

area.

 Secure non stable work piece with a clamp, vice or other adequate

holding device.

 Avoid unintentional starting.

 WARNING! ensure correct air pressure is maintained and not

exceeded.

 Keep air hose away from heat, oil and sharp edges. Check air

hose for wear before each use, and ensure that all connections

are secure.

 DO NOT force the hammer to achieve a task it was not designed

to perform.

 DO NOT operate the hammer if any parts are damaged or missing

as this may cause failure or possible personal injury.

 WARNING! DO NOT cut, grind, saw, sand any materials

containing asbestos.

 DO NOT switch the hammer on whilst the chisel is in contact with

the workpiece.

 DO NOT carry the by the hose, or yank the hose from the air

supply.

 DO NOT hold the workpiece by hand. Use clamps or a vice (not

included) to secure the workpiece. Available from your Sealey

dealer.

 DO NOT allow untrained persons to operate the hammer.

 DO NOT operate the hammer when you are tired, under the

influence of alcohol, drugs or intoxicating medication.

 DO NOT use hammer where there is flammable liquids, solids or

gases such as paint solvents, including waste wiping or cleaning

rags etc.

 DO NOT leave the hammer operating unattended.

 DO NOT carry the hammer with your finger on the power switch.

 DO NOT direct air from the air hose at yourself or others.

 When work is complete ensure the air supply is turned off.

 When not in use disconnect from the air supply and store in a

safe, dry, child proof area.

INSTRUCTIONS FOR:

AIR HAMMER

MODEL NO: SA120.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

The recommended hook-up is shown in fig 1.

2.1. Ensure the air valve is in the "off" position before connecting to the air supply.

2.2. You will require an air pressure of more than 6bar (90psi) , and an air volume of

more than 4cfm for operating the unit.

2.3.  WARNING! Ensure the air supply does not exceed 140PSI while

operating the hammer. Too high an air pressure and unclean air will shorten

the product life due to excessive wear, and may be dangerous causing

possible damage and/or personal injury.

2.4. Drain the air tank daily. Water in the air line will damage the tool.

2.5. Clean the air inlet filter screen weekly.

2.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should

be 10mm I.D. and fittings must have the same inside dimensions.

2.7. Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.

2.8 Couplings.Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome this, connect a

leader hose to the wrench. A quick change coupling may then be used to connect the leader hose to the air line recoil hose.

See fig 1 & 2.

2. AIR SUPPLY

fig 1.

1. SAFETY INSTRUCTIONS

fig 2.

Original Language Version

SA120.V2 Issue: 2 - 04/11/09

1 2

Resumo do Conteúdo

Página 1 - SA120.V2

 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment. W

Página 2 - 5. MAINTENANCE

Ensure you have read understood and follow the safety instructions in Section 1.4.1. Attach the retaining spring by holding the front end of the spri

Comentários a estes Manuais

Sem comentários

Bosch Dampfbügeleisen Sensixx´x DA70 i-Temp TDA703021I a Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Eisen Bosch Dampfbügeleisen Sensixx´x DA70 i-Temp TDA703021I a.
Wir stellen 1 PDF-Handbücher Bosch Dampfbügeleisen Sensixx´x DA70 i-Temp TDA703021I a zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung

Bosch Dampfbügeleisen Sensixx´x DA70 i-Temp TDA703021I a Bedienungsanleitung (2 Seiten)

Marke: Bosch | Kategorie: Irons | Größe: 0.14 MB |

Inhaltsverzeichnis

'!2E20AC-hgfdad!

Weitere Produkte und Handbücher für Eisen Bosch

Sealey SA120 Manual do Utilizador